+ High rigidity
High-rigidity, high-precision frame, with welded steel board and heat treated, eliminated inner tension of press.
+ Balanced centre of gravity
The transmission centre is in accodance with the centre of the whole machine, ensure the accurate and stability in pressing
+ Safe and reliable operation
Hight-sensitive clutch/braking added international top double electromagnetic valve and overloading protection device can guarantee the accuracy and safety for sild board running and stopping.
The precision of machine adjusting is up to o.1 mm, safer and quick in production adjusting
+ High-precision
The abrasive sections of crabkshaft,gear,gearshaft are treated by hardening heat treament and followed milling processing, with high abrasion resistant and balance performance, as well as stable performaces. Ensure quality and using life of punch.
+ Automatiztion processing
Can equip all automatic feeders for automatization production, reduce the cost, promote efficiency.
+ Environment-friendly , energy-saving
Attractive appearance, low noise, low consumption, save energy,reflected the advanced design ideas by smooth and simplification appearance.
| MODEL | CN1-110 | |||
| Capacity | 110 | |||
| Item | ton | S | H | L |
| Rated Tonnage Point | mm | 5 | 3.2 | 5 |
| Stroke Length | mm | 100 | 60 | 180 |
| Stable Speed | s.p.m | - | - | 50 |
| Speed Changing | s.p.m | 45-95 | 60-130 | 30-65 |
| Die Height | mm | 390 | 410 | 350 |
| Maximum Counterbalancer Capacity | kg | 610 | ||
| Slide Adjustment | mm | 90 | ||
| Bolster Area | mm² | 1150×600 | ||
| Bolster Thickness | mm | 110 | ||
| Slide Area(L.RxF.B.) | mm² | 650x470x80 | ||
| Air Pressure | kg/cm² | 6 | ||
| Stable Speed | HPxP | 10x4 | ||
| Speed Changing | HPxP | frequency conversion 15x4 | ||
| Slide Adjusting | HPxP | 0.5×4 | ||
| Precision | GB (JIS) Class1 level | |||
| Die Cushion | M4-350-80 | |||
| Air Pressure | kg/cm² | 6.7 | ||
| Die Cushion Capacity | ton | 8 | ||
| Pad Area(L.RxF.B.) | mm² | 500×300 | ||
| Machine dimension(LxWxH) | mm | 1500x1950x3200 | ||
| Machine Weight | kgs | 9500 | ||
outacplex products are widely used in the industries of electrical motor and electric appliances manufacturing,automobile manufacturing,household electric appliances,meters and instruments,medical facilities,hardware etc.
| Accessories | Standard |
| Hydraulic over-load protector | |
| Slide adjust device (CN1 below 60) |
|
| Slide adjust device (CN1 60 or more) |
|
| Die height indicator (CN1 60 or more) |
|
| Balance device | |
| Balance cam switch | |
| Crank angle indicator | |
| Power supply | |
| Electrical stroke counter | |
| Preset counter | |
| Preset counter | |
| Air source receptacle | |
| Over-run safety device | |
| Maintenance tool box | |
| Operation manual |
| Accessories | Optional |
| Grease Pumb | |
| Pneumatic die cushion device | |
| Inverter | |
| Foot switch | |
| Quick die change device ( Die lifter,clamp and die arm sepjes) |
|
| Slide knock-out device | |
| Misfeed detection consent | |
| Anti-vibration press consent | |
| Photo-electronic safety device | |
| Feeder | |
| Uncoiler | |
| Leveler | |
| Robot | |
| Die room light |
+ Motion detector monitor broken shaft, crankshaft, excessive wear of lining, engagement and disengagement of clutch and brake device.
+ Motor status (Forward / Reverse / Consumption / SPM) displayed on HCI Displaying Screen, with the setting function.
+ Dual-circuit protection for safety light curtain and overrun.
+ Panel-displayed operation modes and Error Messages with Trouble-shooting instruction.
+ Panel setting cam ON/OFF angel from HCI Displaying Screen.
+ 6-spare-cams as standard, and increase of 16-spare-cams can be added as options without mechanical modifications
+ Brake Monitor is equipped with automatic slip-angle correction within a limited range against inaccurate TDC stop position caused by lining wear and change of slide speed.
+ Total counter, Pre-Set counter, Chop counter, Maintenance counter,and Life Counter are all provided.
+ Setting figures and Status of counters all displayed from HCI Displaying Screen.
+ Cam angle controlled misfeed detection circuits A1 & B1 can be set for ON/OFF, and A2 & B2 can be set for all-time detection. A and B port can be set individually.
+ RS-485 module isavailable for thetelegraph-communication monitoring and controlling.
+ Simultaneously monitor up to 256 presses to improve prod action management.
+ Provide on-line Trouble-Shooting procedures with error messages,
+ Illustrate statistical reports of production efficiency and output.
| MODEL | CN1-110 |
| Slide Area(L.RxF.B.) | 650x470 |
| T-slot type | B |
| T-slot number | 2 |
| Mold shank apertureΦ d | Φ50 |
| b3 | 150 |
| b4 | - |
| MODEL | A | B | C |
| a | 22 | 28 | 18 |
| b | 37 | 48 | 30 |
| c | 24 | 28 | 18 |
| d | 16 | 20 | 12 |
| R | 1 | 1 | 1 |
| MODEL | CN1-110 | |
| T-slot type | B | |
| T-slot number | 3 | |
| Number of die pad pin holes x Aperture | 24×Φ28 | +0.5 +0.1 |
| c x d | 75×75 | |
| b1 | 250 | |
| b2 | - | |
| e x f | 400x200 | |
| R | 30 | |
| g | 480 | |
| h | 530 | |
| MODEL | CN1-110 | ||
| Item | S | H | L |
| A | 1680 | 1770.5 | |
| B | 1172 | ||
| C | 2997 | 3030 | |
| D | 1150 | ||
| E | 600 | ||
| F | 650 | ||
| G | 470 | ||
| H | 852 | ||
| I | 430 | 410 | 530 |
| J | 628 | ||
| K | 310 | 350 | |
| L | 1420 | 1531 | |
| M | 1050 | ||
| N | 932 | ||
| O | 1870 | 1961 | |
| P | 250 | ||
| Q | 1498 | 1495 | |
| R | 760 | ||
| S | 2100 | ||
| T | 3180 | 3304 | |
